#Laser jump speed full

Their IP65 ratings make them suitable even for some of the harshest environments. Our i-Tech laser marking systems provide flexible installation through their modular design. Domino Amjet's D-Series i-Tech range of 10-watt, 30-watt and 60-watt CO2 laser marking systems deliver flexible, high-speed, high-quality coding across a wide variety of materials, with the ability to produce multiple lines of text, making it an ideal industrial-level CO2 laser printing solution.

#Laser jump speed full

Cutting an unknown material risks bodily harm and damage to equipment/facilities.Not to be confused with our full range of F-Series Fiber Lasers, our D-Series are small, yet powerful CO2 laser solutions that can print on a number of substrates. Only approved materials should be cut, and banned materials should never be placed in or even around the laser cutter. This can save you a lot headaches.Д¬utting a bad material in the laser cutter can be dangerous. It is always highly recommended that you do some small test cuts/engraves before running your full design, especially if it is large or uses valuable material and/or you haven't lasered it before. Speed and Power SettingsД®very material and sometimes even every day is different, but here are some starting points: Change the starting position and/or resize your file so that it fits on the bed. The file is going to run off one of the edges of the machine. If this continues to happen notify the fab lab team Can't run file, 'Frame Slop' error displayed on panel. Head position has been lost and the head has hit a limit switch. 'Hard Limit Prot.' error displayed on panel Ventilation fan needs to be cleaned, notify the fab lab team The head hits the side of the machine.The Laser is out of alignment and needs to be adjusted, notify the fab lab team Fumes are not venting well. Edges of cut pieces are slanted, rather than straight.The power supply is in the left side of the cabinet behind the lower left door would indicate this is the case.) P0 on the power supply is an indicator of it being broken. Check the door switch to make sure it is not broken (Close the lid.Open the door and reclose (the door switch might be flakey).Try focusing the laser cutter by hand if you like and notify the fab lab team The laser doesn't fire.If none of these work, notify the fab lab team Lines are cutting fuzzier and thicker than normal.Check to see if the upper z-limit switch is stuck.Wiggle the probe and make sure its not jammed.If you are using the rotary axis, refer to this page Troubleshooting Guide Sample of hardboard - Letter shapes are engraved, outline is cut When Finished After cut is finished allow ~30 seconds before opening to vent smoke/fumes.Press 'Frame' to outline your job and check that it fits.Jog head to center of media using control panel.Press Z/U on control panel and use left/right arrows to lower the bed until your material will fit under the head.Turn on the laser cutter using your badge and the green button.Check the calendar to make sure you're not running into a reservation.Separate operations into different layers for each speed and power setting.LightBurn accepts the following file types:.Do not create your designs on the computers connected to the lasers.Beware of flammable materials while using the machineДesign step 1: Create your design in your favorite graphics program.Make sure the air compressor, blower fans, and chiller are on.Press power button and scan your keycard.See the list of approved/banned materials on this wiki Do not cut unapproved, unknown or banned materials on the laser cutter. Many materials give off toxic fumes when cut. Lasers can cause serious eye damage, even indirectly through scattered energy. Do not bypass any safety lockouts or open panels without consulting the fablab lead first. The laser is encased and will not fire unless the doors are shut. Post on the forum about it, or send an email to Someone from the laser group will check the machine, clean as necessary, and put it back into service.Place a note that a fire occurred and the machine is out of service.A Carbon Dioxide (CO 2) fire extinguisher is located next to the laser cutter.This will shutdown the laser and the air supply Hint: Hit the big, red, emergency stop button.Move the head out of the way, if it's small.Never override laser cutter safeties and switches.Never cut materials that you don't know are safe.Never leave the laser cutter unattended while it was powered on (even if it is not firing).You may only use the laser cutter if you have been officially authorized according to the machine access policy.A high intensity beam of laser light can produce extremely high temperatures as it comes into contact with the materials it is engraving, marking, or cutting.